|
Toby Corp of America Amplifier Recommendations |
|
|
|
|
Brand |
Power Rating |
Speaker Wiring Type |
Use for |
Price |
Notes |
|
|
|
| |
|
|
|
|
|
|
|
|
|
Rockford Fosgate |
|
|
|
|
|
|
|
|
P200-2 |
100 X 2 @ 4ohm |
Stereo |
Sheriff |
249 |
|
|
|
|
|
P300-1 |
300 X 1 @ 2ohm |
Bridged/Series (not sure yet) |
Marshal/Ranger |
299 |
Need to test Wiring Type |
|
|
Alpine |
|
|
|
|
|
|
|
|
|
Mrp-F250 |
100 X 2 @ 4ohm |
Stereo |
Sheriff |
230 |
Amp bridged from 4 channels to 2 |
|
Mrp-F300 |
150 X 2 @ 4ohm |
Stereo |
Sheriff/Marshal/Ranger |
230 |
Amp bridged from 4 channels to 2 |
|
Mrp-M450 |
220 X 1 @ 4ohm |
Series Speaker |
Marshal/Ranger |
230 |
Very powerful for Ratings… DO NOT BRIDGE |
|
JL Audio |
|
|
|
|
|
|
|
|
|
250/1v2 |
250 X 1 @ 1.5ohm |
Series(Sheriff)/Bridged(Others) |
Sheriff/Marshal/Ranger |
~309 |
|
|
|
|
|
300/2v2 |
300 X 1 @ 3ohm |
Stereo |
Marshal/Ranger |
~319 |
|
|
|
|
|
Kicker |
|
|
|
|
|
|
|
|
|
ZX250.2 |
125 X 2 @ 2ohm |
Stereo |
Sheriff |
~120 |
|
|
|
|
|
ZX300.1 |
300 X 1 @ 2ohm |
Bridged/Series (not sure yet) |
Marshal/Ranger |
~130 |
Need to test Wiring Type-Not sure of output |
|
ZX400.1 |
400 X 1 @ 2ohm |
(Probably) Series |
Marshal/Ranger |
~170 |
Need to test Wiring Type-Not sure of output |
|
Pioneer |
|
|
|
|
|
|
|
|
|
GM-5300T |
125 X 2 @ 4ohm |
Stereo(Sheriff) Series(Others) |
Sheriff/Marshal/Ranger |
160 |
Bridge amp For Marshal/Ranger |
|
MA Audio |
|
|
|
|
|
|
|
|
|
M300XE |
125 X 2 @ 4ohm |
Stereo |
Sheriff/Marshal/Ranger |
~130 |
Might need to be set with low gain for Sheriff |
|
HK398 |
150 X 2 @ 4ohm |
Stereo |
Marshal/Ranger |
~180 |
Need to check actual power output… |
|
Eclipse |
|
|
|
|
|
|
|
|
|
XA1000 |
320 X 1 @ 4ohm |
Series |
Marshal/Ranger |
~200 |
Very powerful… DO NOT BRIDGE |
|
MTX |
|
|
|
|
|
|
|
|
|
TC4002 |
100 X 2 @ 4ohm |
Stereo |
Sheriff/Marshal/Ranger |
~200 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
Disclaimer: This page is just suggestions for amps I believe are of
high quality and will provide a good sound when used with a Toby
Speaker Cabinet. |
|
We have NO CONTROL over the way that your amplifier has been set or
the way it was installed. Therefore, TobyCorp
offers No Guarantee that |
|
while using one of these amplifiers you will not have a problem with
burning up one of our drivers. Professional Installation and Setting
of your amp |
|
is Definitely recommended and may minimize problems. Any of these
amps may give you issues IF SET IMPROPERLY with the gain too high
or |
|
improperly set crossover points. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
TobyCorp recommends Never using a "Bass Boost" function of an
amplifier, or the ever so popular "Bass Knob" which |
|
|
|
controls the boost setting. Our cabinets are engineered for optimal
clarity and volume without the use of this function. |
|
|
| |
|
|
|
|
|
|
|
|
|
Crossover point for our subs should be set to approx. 110Hz on the
"Low pass" setting. |
|
|
|
|
|
